Header Ads

How to Downgrade BM622m - BM623m Package Date 2013

How to Downgrade BM622m - BM623m package date 2013


Lecture muna tayo :

Question: Bakit Gusto ng iba na downgraded yung modem nila?

Sagot : kasi yung package date 2013 yung mga firmware ( software version) nila  ay naka fix at uncheckable yung   LAN Telnet at  SSH  , pag 2012 na firmware  madali mag change at gamitin pang HUNT  - SNIPE  dahil pwede i check yung box ng telnet.

Vulnerability :  pag tanga yung user aksidente nya ma checheck yung WAN , at  naka default yung user  pass ng  admin   pwede generate  yung Serial at WAN Mac
 Kung  ako tatanungin kung di nyo naman pang ssnipe yan  mas ok pa ako sa 2013 mas ok firewall nyan

Ganito yung  622m 623m  2013  unchekable yung box ng  LAN Telnet/SSH kaya need  natin ng webdeveloper  pang check ng box   or old school inspect element to enable the checkbox lagi ganun yan pag 2013 lagi mo check muna click apply bago mag change mac ulit


Tips ko bago  mag DOWNGRADE UPGRADE ENABLE mo muna yung TELNET
(Enable Telnet First Before Downgrading)




Software Version :

Hindi porket  2013  yan para pareho na yan iba iba yung software version nyan.
Paano malalaman anong software version at packate date yung  modem.

Kung 622m user ka type mo 192.168.254.1 sa browser mo
This  what  you can find ..

Software version of Package Date 2012 is B016  (16) last 
Software version of Package Date 2013 are  B019 , B021, and B022 

Note: version 16 and  version 19  change mac command  is the same
while B021 and B022 BM622m  change mac command is similar to BM623m Change Mac Command





For 623m user  type  192.168.254.254
Package Date 2013  Software version BO12 , B013


How to Downgrade

There are  two ways to  downgrade  , you can  log in  on web gui or upload firmware using Winspreader tools.

First Upload Mybro or Greenpacket  because you cannot direct upload 622m (low space or invalid firmware) Do the Step below...
2nd Upload 622m B016 Firmware... repeat the step below



WEB GUI Upgrade

1.Uploading by  log in as admin or user (inspect element on user only)
under maintenance tab  device / firmware
(same thing to do with Smart or GP firmware)
2. Select firmware and click upgrade GP or Mybro
3. Observe the percentage or Signal lights wait if  100% success or failed try re upload other firmware noted below this post
4.If firmware upload success do a Hard RESET
5.If your already have change  GP or Mybro  upload 622m firmware repeat step 1 to 4.



Sa may Mybro or Green Packet





Uploading  Firmware via Winspreader.

1. Get a Winspreader  save it on your desktop and   firmware you desired..(GP or Smart)
2. Open a Winspreader   browse the  desired firmware  Hit start.
3. Plug your Modem  Power and Lan Cable  the  wait  a  few minutes....
NOTE if your Modem is already plug in before doing step 2 ,  please do unplug the power adapter first then re plug the power adapter.
4. check the web GUI ..  type the   192.168.254.1  on your browser
5. If you Gui Change to Smart...
6.Do a Hard Reset by Press and hold  it 2 minimum of 2 minutes  ( sundutin mo ng malufet wag moaalis sa pag kakasundut )
7.If your already have change  GP or Mybro  upload 622m firmware repeat step 1 to 6. 






Available Firmware Online

All featured tar file here  can be upload on your mediatek modem  622m 623m  even the Smart Mybro GreenPacket firmware (GP)  you can use it...

NAKIKITA NYO YUNG GOOGLE CUSTOM SEARCH sa RIGHT SIDE??
Click mo SEARCH  then  input mo "Firmware Collection"   ganyan mag Google dito!






Observing Signal Lights while Uploading Firmware :Very Important

You should observe the signal light blink sequence when uploading firmware
When the uploading start signal light blink like a charging  battery on your phone
SLOWMO Sequence from  1 , 2 , 3 ,4 ,5  or   1 and 5  , 2  and 4, 

If the signal light are steady , usually it stop   at 1 and 2 or  3 signal lights are ON Uploading Firmware is Finish..



NOTE: Failed  Upload Firmware   Signal Sequence  is  too FAST!!     12345 - 12345
Meaning Firmware upload Failed


HARD RESET : Very Important

Take note this for every success  upload firmware  Please DO a Hard RESET
  1. Press and Hold  reset button minimum of  1 to 2 minutes.
  2. all lights up first
  3. Observe the lights  blink sequence   similar on light  repeated sequence when uploading
  4. 1 and 5  will lights  , then   2 and 4 last 3( repeated)
  5. sometimes    1, 3, 5, 2,4  blink sequence.
  6. all signal light turn of   while Power and LAN  are still on 
  7. Hard RESET Finish

This What Happen If you DO NOT Follow the HARD RESET  Un proper IP config for firmware

Instead  622m IP it is  Mybro IP , Do a Hard Reset to Fix



Instead  of Mybro IP  it is a 623m IP ,Do a HARD RESET  to Fix



WHAT IF FIRMWARE UPLOAD FAILED?

This is a very common  firmware upload failed because the present firmware is too big and there is no enough space to re upload new firmware and extract it to the mediatek chip.

SOLUTION:  upload a low space firmware  like Mybro   or GP firmware .
Do the step above.. then after success upload  GP or Mybro.. You can upload 622m Firmware B016 same step above gui or winspreader.

NOTE: Hard reset or signal light on Mybro sometimes only 1 and 2 are on.. 

Very important do the Hard Reset for every downgrade to upgrade.. Kumbaga sa pag rereformat ng computer eto yung final stage.. dahil di mag tatake effect yung new firmware settings pag di ka nag restore default..

Question:
Bakit ayaw mag upgrade  sa gui ng Mybro nag oopen lang yung Browse?
Huwag gamitin yung mouse sa pag select ng menu ..pag naka select kana ng firmware  gamitin ang TAB sa keyboard sa pag select ng upgrade makikita mo may  line_ _ _ _   sapligid ng upgrade/upload  Press mo Enter sa keyboard.. mag pro proceed   kana sa upgrading.. Tips ko mas maganda gamitin ang FireFox browser.

Bakit walang WiFi  noong naging Mybro or Gp yung firmware?
walang WiFi talga yung sa Mybro kaya dapat 622m yung firmware nyo talga dyan or balik nyo sa 623m..

Bakit di ako maka log in?
Baka di nyo pa ginawa yung Hard Reset  tapos na iwan pa yung setting ng previews firmware at kada palit ng firmware mag iiba talga user nyan after ng hard reset at upload ng firmware , may sample sa itaas  yung iba yung IP sa Firmware..


--Kung gusto nyo pasukin admin ng Mybro or GP try nyo mag change mac gamit yung mga scripts dito pang change mac kasama sa scripts yun.. 
after mag change mac gamit yung tools 

Click Here to Download


admin user
user:admin password:smart
user:admin  password:admin   (default sa gp)

default  user only (not admin )
user:smart  password;smart
user:user  password:user   (gp) 

admin user for 622m firmware click Here

No signal Lights   lagyan ng signal lights?

Now open a telnet again
Telnet 192.168.15.1 ( yung IP dipende sa Firmware mo  at user password sa Telnet)


BM622m  Firmware

Login:Firefly
Pass:$P4mb1h1r4N4m4nT0!! 
(copy paste mo yan kung windows 8 or 7 ka mouse kung windows 10 ka pwede ctrl+v paste invisible yan press enter)
rm etc/default.cfg  ( Enter )
reboot   (Enter)


Greenpacket or SmartBro
telnetUserName :mt7109
telnetPassword : wimax
 
rm etc/default.cfg  ( Enter )
reboot   (Enter)







Di ako makapag change mac  sa Mybro or GP?
gamit ka ng pang open or back door .. sample tools a available sa internet  chicnagatas or media karne hindi ka mag kaka problema dyan kung inopen muna yung Telnet before ka mag upgrade..

Enable Telnet for 622m
login on your browser type 192.168.254.1
username: user
password: 0SlO051O

open a new tab on your browser  copy paste this link
http://192.168.254.1/advanced/acl.htm


You might also like:

How to fix Huawei BM622m No Signal Lights , Ready Only, and Continues LAN Refresh +1970








1 comment

mark vincent bata-anon said...

sir pa konting help naman po sa 623m ko habang nag do-downgrade sa GP firmware namatay po pc ko. ang nangyare power at lan nalang po ang umiilaw tapos di ko na po ma access ang GUI pero napiping ko sya sa 192.168.254.254. ano po bang tools ang pwede gamitin dito? hindi na po kasi gumagana yung reset botton sa likod simula nung nag failed ang donwgrade nya

blogmytuts. Powered by Blogger.